1、檢測雙組份打膠機的供膠管路是否通暢，混交棒是否完好。因為我們使用膠體的特質決定的供膠管路非常容易杜塞，如果對方平時沒有注意對設備保養那么有很大的可能會堵塞、混交棒損壞，如果這部分損壞的話設備的出膠量會變得不正常甚至會出現花膠的情況出現。

　　1. Test whether the glue supply pipeline of double component glue machine is unobstructed and whether the mixed rod is intact. Because we use the glue line colloid characteristics determine very easily Dusseldorf, if you usually do not pay attention to equipment maintenance so great may be blocked and mixed rod damage, if this part of any equipment to produce the adhesive will become normal or even a flower gum situation.

　　2、打膠機的供嬌壓力如果不夠的話也是會出現這個問題的，因為打膠機的膠體完全靠氣壓來擠出設備并完美的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴。所以我們一定要檢測下我們要購買的雙組份打膠機的壓力系統是否正常，是否能夠正常的調節壓力。

　　2, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass. If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict. So we must check whether we need to buy the pressure system of two sets of glue machine is normal, whether it can regulate the pressure normally.

　　3、排查檢測雙組份打膠機的密封圈以及混合器單向閥，這部分如果損壞的話會導致雙組份打膠機的aB組份比例不對，出現混亂!同時密封圈也算是比較容易損壞的所以我們應當重點排查。

　　3 、 check and test the sealing ring and mixer check valve of the double component rubber breaker, if this part is damaged, it will lead to the aB component proportion of the two component punch machine is not right, and there will be confusion! At the same time, the sealing ring is relatively easy to damage, so we should focus on investigation.

　　雙組份打膠機單向閥

　　One way valve for two component rubber press

　　4、二手雙組份打膠機因其具有超高的性價比所以還是有相當大的一部分企業會選擇二手雙組份打膠機。二手雙組份打膠機在價格上具有極大的優勢，能夠為企業節約一部分資金但是同時也會有各種的風險，這個就需要各個企業在購買二手雙組份打膠機的時候擦亮眼睛了。

　　4, the second-hand two component punch machine because of its high cost performance, so there are still a large number of enterprises will choose the second-hand two component rubber machine. Second hand two component glue machine has great advantages in price, can save part of the money for the enterprise, but there will also be a variety of risks, this requires each enterprise in the purchase of second-hand two-component glue machine to polish eyes.

　　5、我們需要堅持伺服電機減速機間或減速機齒輪間鍵、伺服控制器或電機是否損壞、燒毀。如果這些位置損壞的話會導致我們的雙組份打膠機玻璃打膠機機頭不行走電機不轉的故障

　　5, we need to insist on servo motor reducer or reducer gear key, servo controller or motor is damaged, burned. If these positions are damaged, it will lead to the failure of the two component glue machine glass gluing machine head not to walk and the motor does not turn

　　本文由雙組份打膠機為您提供，我們的網站是:http://linshi.jncsjx.com我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問!

　　In this paper, a two component glue machine to provide you, our website is: http://linshi.jncsjx.com, we will wholeheartedly provide you with better service, you are welcome to visit!