雙組份打膠機在使用過程中如果出現“出花膠”現象，即打出的膠體不均勻、有氣泡或顏色異常等問題，可能是由多種原因引起的。以下是一些常見的原因及相應的處理方法：

　　If there is a phenomenon of "flower glue" during the use of the two-component glue machine, that is, the glue produced is uneven, has bubbles or abnormal color, it may be caused by various reasons. Here are some common reasons and corresponding solutions:

　　一、常見原因分析

　　1、 Common cause analysis

　　配比不準確

　　Inaccurate ratio

　　問題描述：A組分和B組分的比例不符合要求，導致膠體固化不良或性能下降。

　　Problem description: The ratio of component A to component B does not meet the requirements, resulting in poor colloidal solidification or decreased performance.

　　可能原因：

　　Possible reasons:

　　計量泵故障，無法精確控制流量。

　　The metering pump is malfunctioning and unable to accurately control the flow rate.

　　混合管堵塞或損壞，影響混合效果。

　　The mixing pipe is blocked or damaged, which affects the mixing effect.

　　膠桶內的膠液面高度差異過大，導致吸入量不一致。

　　The height difference of the glue level in the glue bucket is too large, resulting in inconsistent suction volume.

　　處理方法：

　　Handling method:

　　檢查計量泵的工作狀態，確保其正常運行。如有必要，進行校準或更換。

　　Check the working status of the metering pump to ensure its normal operation. If necessary, calibrate or replace.

　　清洗或更換混合管，確保其暢通無阻。

　　Clean or replace the mixing tube to ensure it is unobstructed.

　　確保兩個膠桶的液面高度保持一致，避免因液位差導致的配比誤差。

　　Ensure that the liquid level of the two rubber drums remains consistent to avoid mixing errors caused by liquid level differences.

　　混合不充分

　　Insufficient mixing

　　問題描述：A組分和B組分沒有充分混合，導致膠體中出現條紋或顏色不均。

　　Problem description: Insufficient mixing of component A and component B results in stripes or uneven color in the colloid.

　　可能原因：

　　Possible reasons:

　　混合管內部結構設計不合理，無法實現充分混合。

　　The internal structure design of the mixing tube is unreasonable and cannot achieve sufficient mixing.

　　混合管磨損或老化，降低了混合效率。

　　The wear or aging of the mixing tube reduces the mixing efficiency.

　　打膠速度過快，超出混合管的處理能力。

　　The gluing speed is too fast, exceeding the processing capacity of the mixing tube.

　　處理方法：

　　Handling method:

　　選擇合適長度和直徑的混合管，確保其能夠提供足夠的混合時間。

　　Choose a mixing tube of appropriate length and diameter to ensure it can provide sufficient mixing time.

　　定期檢查混合管的磨損情況，及時更換老化的部件。

　　Regularly check the wear of the mixing tube and replace aging components in a timely manner.

　　調整打膠速度，使其與混合管的處理能力相匹配。

　　Adjust the gluing speed to match the processing capacity of the mixing tube.

　　空氣混入

　　Air mixed in

　　問題描述：膠體內含有大量氣泡，影響膠體的外觀和性能。

　　Problem description: Colloids contain a large number of bubbles, which affect their appearance and performance.

　　可能原因：

　　Possible reasons:

　　膠桶或管道內存在空氣，未完全排出。

　　There is air inside the rubber drum or pipeline that has not been completely expelled.

　　打膠機的密封件老化或損壞，導致外界空氣進入。

　　The sealing components of the glue machine are aging or damaged, causing external air to enter.

　　打膠過程中膠槍開關操作不當，產生抽吸效應。

　　Improper operation of the glue gun switch during the gluing process resulted in a suction effect.

　　處理方法：

　　Handling method:

　　在使用前對膠桶和管道進行充分排氣，確保內部無空氣殘留。

　　Before use, fully exhaust the rubber drum and pipes to ensure that there is no residual air inside.

　　檢查并更換老化的密封件，確保設備的密封性良好。

　　Check and replace aging seals to ensure good sealing of the equipment.

　　打膠時避免頻繁開關膠槍，盡量保持連續出膠，減少空氣混入的機會。

　　When applying glue, avoid frequent opening and closing of the glue gun, try to maintain continuous glue dispensing, and reduce the chance of air mixing in.

　　膠桶或管道堵塞

　　Blockage of rubber drum or pipeline

　　問題描述：膠液流動不暢，導致出膠不穩定或中斷。

　　Problem description: Poor flow of adhesive, resulting in unstable or interrupted dispensing.

　　可能原因：

　　Possible reasons:

　　膠桶內的膠液凝固或沉淀，堵塞進料口。

　　The glue liquid in the glue bucket solidifies or settles, blocking the feeding port.

　　管道內有異物或雜質，阻礙膠液流動。

　　There are foreign objects or impurities in the pipeline that hinder the flow of the adhesive solution.

　　長時間未使用，膠液在管道內固化。

　　Long term disuse causes the adhesive to solidify inside the pipeline.

　　處理方法：

　　Handling method:

　　定期清理膠桶，防止膠液凝固或沉淀。可以使用專用的清洗劑進行清洗。

　　Regularly clean the glue bucket to prevent the glue from solidifying or settling. Special cleaning agents can be used for cleaning.

　　檢查管道內是否有異物或雜質，必要時進行疏通或更換。

　　Check for foreign objects or impurities in the pipeline, and if necessary, clear or replace them.

　　如果長時間不使用，建議將管道內的膠液排空，并用清洗劑沖洗干凈，防止固化。

　　If not used for a long time, it is recommended to drain the adhesive in the pipeline and rinse it clean with a cleaning agent to prevent solidification.

　　溫度影響

　　Temperature influence

　　問題描述：環境溫度過高或過低，影響膠液的流動性或固化速度。

　　Problem description: The environmental temperature is too high or too low, which affects the fluidity or curing speed of the adhesive solution.

　　可能原因：

　　Possible reasons:

　　環境溫度過低，膠液粘度增加，流動性變差。

　　The ambient temperature is too low, the viscosity of the adhesive increases, and the fluidity deteriorates.

　　環境溫度過高，膠液提前固化，導致出膠不均勻。

　　The high ambient temperature causes the adhesive to solidify prematurely, resulting in uneven dispensing of the adhesive.

　　處理方法：

　　Handling method:

　　根據膠液的特性，選擇合適的環境溫度范圍進行操作。通常，室溫（20-25°C）是較為理想的溫度。

　　Select the appropriate ambient temperature range for operation based on the characteristics of the adhesive solution. Usually, room temperature (20-25 ° C) is the ideal temperature.

　　如果環境溫度較低，可以使用加熱裝置對膠桶進行預熱，提高膠液的流動性。

　　If the ambient temperature is low, a heating device can be used to preheat the glue barrel and improve the fluidity of the glue solution.

　　如果環境溫度較高，可以采取降溫措施，如使用風扇或空調，避免膠液過早固化。

　　If the ambient temperature is high, cooling measures can be taken, such as using fans or air conditioning, to avoid premature curing of the adhesive.

　　膠液質量問題

　　Quality issues with the adhesive solution

　　問題描述：膠液本身存在質量問題，導致出膠異常。

　　Problem description: The adhesive itself has quality issues, resulting in abnormal dispensing.

　　可能原因：

　　Possible reasons:

　　膠液儲存不當，受潮、受熱或過期，導致性能下降。

　　Improper storage of adhesive solution can lead to performance degradation due to moisture, heat, or expiration.

　　組分和B組分的批次不同，配伍性不佳。

　　The batches of component and component B are different, resulting in poor compatibility.

　　膠液中含有雜質或污染物，影響其性能。

　　The adhesive contains impurities or pollutants that affect its performance.

　　處理方法：

　　Handling method:

　　確保膠液存放在干燥、陰涼的地方，避免陽光直射和高溫環境。

　　Ensure that the adhesive is stored in a dry, cool place, away from direct sunlight and high temperature environments.

　　使用同一批次的A組分和B組分，確保其配伍性良好。

　　Use the same batch of component A and component B to ensure good compatibility.

　　在使用前檢查膠液的質量，確保其無異味、無沉淀、無變色等異常現象。

　　Before use, check the quality of the adhesive to ensure that it has no odor, sediment, discoloration or other abnormal phenomena.

　　二、預防措施

　　2、 Preventive measures

　　為了減少“出花膠”現象的發生，建議采取以下預防措施：

　　To reduce the occurrence of "flower gum" phenomenon, it is recommended to take the following preventive measures:

　　定期維護設備：定期檢查和維護打膠機的各個部件，確保其正常運行。特別是計量泵、混合管、密封件等關鍵部件，應定期清洗和更換。

　　Regular maintenance of equipment: Regularly inspect and maintain the various components of the glue machine to ensure its normal operation. Especially for key components such as metering pumps, mixing pipes, and seals, they should be cleaned and replaced regularly.

　　正確操作設備：嚴格按照設備的操作規程進行操作，避免誤操作或不當使用。打膠時應保持穩定的出膠速度，避免頻繁開關膠槍。

　　Proper operation of equipment: Strictly follow the operating procedures of the equipment to avoid misoperation or improper use. When applying glue, a stable dispensing speed should be maintained to avoid frequent opening and closing of the glue gun.

　　選擇優質膠液：選用質量可靠的雙組份膠液，確保其符合產品要求。避免使用過期或儲存不當的膠液。

　　Choose high-quality adhesive solution: Choose reliable two-component adhesive solution to ensure it meets product requirements. Avoid using expired or improperly stored adhesive.

　　保持環境清潔：工作環境應保持清潔，避免灰塵、雜物等進入膠桶或管道。定期清理設備周圍的雜物，確保良好的操作環境。

　　Keep the environment clean: The working environment should be kept clean to prevent dust, debris, etc. from entering the glue bucket or pipeline. Regularly clean the debris around the equipment to ensure a good operating environment.

　　合理設置參數：根據膠液的特性和實際需求，合理設置打膠機的參數，如配比、壓力、速度等，確保最佳的打膠效果。

　　Reasonable parameter setting: Based on the characteristics and actual needs of the glue solution, set the parameters of the glue machine reasonably, such as ratio, pressure, speed, etc., to ensure the best glue effect.

　　三、總結

　　3、 Summary

　　雙組份打膠機出現“出花膠”現象可能是由多種因素引起的，包括配比不準確、混合不充分、空氣混入、膠桶或管道堵塞、溫度影響以及膠液質量問題等。通過仔細檢查設備、調整操作參數、選擇優質膠液以及定期維護保養，可以有效解決這些問題，確保打膠機的正常運行和膠體的質量。如果問題持續存在或無法自行解決，建議聯系專業的技術人員或設備供應商尋求幫助。

　　The phenomenon of "flower glue" appearing in the two-component gluing machine may be caused by various factors, including inaccurate proportioning, insufficient mixing, air mixing, blockage of the glue bucket or pipeline, temperature influence, and quality problems of the glue solution. By carefully inspecting the equipment, adjusting operating parameters, selecting high-quality glue solution, and regular maintenance, these problems can be effectively solved to ensure the normal operation of the glue machine and the quality of the glue. If the problem persists or cannot be resolved on its own, it is recommended to contact professional technicians or equipment suppliers for assistance.

　　本文由 雙組份打膠機 友情奉獻.更多有關的知識請點擊   http://www.xyspace.net  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待

　　This article is a friendly contribution from a two-component glue machine For more related knowledge, please click http://www.xyspace.net Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon