The daily maintenance and upkeep strategy of insulating glass equipment is a matter that insulating glass processing plants should always pay attention to. Once any abnormalities are found in the insulating glass equipment, immediate maintenance should be carried out to ensure the safe operation of the insulating glass. To ensure the production efficiency of insulating glass, enterprises often encounter a series of problems during the production process of using insulating glass equipment. Due to the staff not knowing how to handle them, the faults are even worse. At this time, the manufacturer needs to provide training to the staff before starting the machine, so as to timely respond to the problems that occur in the production process of insulating glass equipment. In addition, some equipment operations may also involve staff changes and departures, and understanding and proficiency in the operation of the equipment are also important.

中空玻璃生產過程當中一定要注意細節，包括中空玻璃設備的使用維修及中空玻璃的材料選用都很關鍵。比如中空玻璃生產過程中，中空玻璃內部結霧。產生原因：由于二道密封劑質量不穩定或質量不過關，在陽光的照射下?lián)]發到中空玻璃內部導致結霧；或者是干燥劑質量差，在太陽光照射下，釋放低分子物，導致結霧。

During the production process of insulating glass, it is important to pay attention to details, including the use and maintenance of insulating glass equipment, as well as the selection of insulating glass materials. For example, during the production process of insulating glass, fog forms inside the insulating glass. Reason for occurrence: Due to the unstable or substandard quality of the second sealing agent, it evaporates into the interior of the insulating glass under sunlight, resulting in fogging; Or it may be due to poor quality of the desiccant, which releases low molecular weight substances under sunlight, leading to fogging.

丁基膠涂膠機是中空玻璃設備中的必須要用的設備，主要的功能是給鋁框涂丁基膠的，也是使用比較頻繁的設備。當遇到丁基膠涂布機擠出的丁基膠，出現毛刺不光滑時的解決方法。如果是新設備，應先觀察出膠孔是否光滑，如果出膠孔粗糙，應先打磨，再試機器；舊機器，由于設備的溫度傳感器有時不靈敏，顯示的溫度與實際的不相符，這時就需要將溫度進行上調，直到出膠正常為止。當遇到丁基膠不沾鋁條和玻璃時，是由于溫度的影響造成，建議將溫度進行上調到合適為止。

The butyl adhesive coating machine is a necessary equipment in insulating glass equipment, and its main function is to apply butyl adhesive to aluminum frames, which is also a frequently used equipment. When encountering the butyl adhesive extruded by the butyl adhesive coating machine, there is a solution to the problem of uneven burrs. If it is a new equipment, it is necessary to first observe whether the adhesive hole is smooth. If the adhesive hole is rough, it should be polished first and then the machine should be tried again; In old machines, due to the temperature sensor being sometimes insensitive, the displayed temperature does not match the actual temperature. Therefore, it is necessary to increase the temperature until the glue is released normally. When encountering butyl adhesive not adhering to aluminum strips and glass, it is due to the influence of temperature. It is recommended to raise the temperature to a suitable level.