雙組份打膠機出現花膠的問題無論是進口的立式打膠機還是臥式打膠機都會經常出現的一種故障，雙組份打膠機一般出現花膠這種故障大多是由以下幾個原因導致的。
　　A two-component glue machine it is a question whether the fault will often imported vertical glue machine or horizontal gluing machine, two-component glue machine generally it is mostly the fault caused by the following reasons.
　　1、雙組份打膠機的混膠器內膠體過多固話，阻力增大。
　　1, the colloid in the double component glue machine is too much colloid, and the resistance is increased.
　　2、A或B膠膠桶內無膠，膠已用完。
　　2, A or B glue barrel has no glue, the glue has been used out.
　　3、A或B膠膠桶內有空氣。
　　There is air in 3, A or B rubber buckets.

　　4、針閥或單向閥堵塞。我們仔細觀察小編所寫的導致花膠的故障原因會發現大多是由于設備沒有定期維護清洗導致的。所以我們一定要牢記設備一定要定期維護清洗的良好習慣。
　　4, needle valve or one-way valve blockage. We carefully observe the small write failure reason it will find mostly because the device is not regular maintenance cleaning result. So we must keep in mind that the equipment must maintain the good habit of cleaning regularly.
　　一種情況是由于我們將打膠機的打膠速度設置的過快導致的。有的客戶為了加快自己的生產節奏追趕生產計劃，將打膠速度認為調整的過快，導致膠體還沒有完全達到合格標準機頭就已經移動到下一個位置進行打膠操作了.
　　One of the cases is that we set the sizing speed of the glue machine too fast. In order to speed up their production rhythm and catch up with production plan, some customers think that the speed of glue is too fast, which leads to the fact that the gel has not yet reached the standard of qualification, and the machine head has moved to the next location to do glue operation.
　　如果我們需要加快打膠的速度調整了打膠機的移動參數的話，那么我們對應的也應該對供膠系統也進行相應的設置，比如這時候我們就需要加大供膠壓力，增大打膠機的出膠速度來配合對象的移動速度的增加。
　　If we need to accelerate the speed of adjustment of the glue glue machine the movement parameters, then we should also carry out corresponding setting on the glue supply system, for example, this time we need to increase the glue supply pressure, increase the speed of glue machine glue to match the speed of the moving object shift increases.
　　如果我們僅僅是單獨的增加了打膠機的移動速度而沒有對壓力進行調節的話就很有可能出現打膠不飽滿的情況發生。另外一種情況跟打膠機的速度差不多就是我們的供膠壓力不足導致的。
　　If we increase the speed of the glue machine alone instead of adjusting the pressure, it is very likely that we will not get enough glue. The other is about the speed of the rubber machine, which is caused by our lack of adhesive pressure.
　　產生打膠不飽滿的原因可以參考種情況。除了以上小編說的人為原因導致的這個故障以外設備的零部件損壞也會導致這個問題，比如機頭感應器損壞。
　　The reason why the glue is not full can be referred to the first situation. Damage to the parts of the equipment, such as the head inductor damage, can also be caused by the damage to the parts of the equipment other than the man-made causes mentioned above.
　　公司始終堅持不斷進行管理創新和科研創新，將以優良的品質、的售后服務贏得廣大客戶的信賴與支持，歡迎廣大新老客戶來我公司實地考察，洽談合作！
　　The company always insists on continuous management innovation and research innovation, and will win the trust and support of our customers with excellent quality and perfect after-sales service. Welcome new and old customers to come to our company for field visits and discuss cooperation.