很多時候我們在使用中空玻璃打膠機時感覺不順暢，但是具體還說不出到底是那里出現了問題。這時候就要去找廠家詢問、資訊，或者更嚴重的花錢讓售后來維修。今天小編就給大家總結一下，關于中空玻璃雙組份打膠機會出現的那些問題現象、問題的因素以及解決辦法。
Sometimes we feel bad when we use the hollow glass gluer, but we can't tell exactly where the problem is. At this time, you have to go to the manufacturer for inquiries, information, or even more serious money for later maintenance. Today I'll give you a summary of the problems, phenomena, factors and solutions of the two-component gluing opportunities for hollow glass.
問題1：在打膠過程中，有時還沒有打完就開始以后的動作。
Question 1: In the process of gluing, sometimes the action after the gluing is started before the gluing is finished.
這種情況下是非常不好的，很容易損壞玻璃，那么這種現象出現的原因有以下哪幾種呢，我們一起來看一下。
In this case, it is very bad. It is easy to damage the glass. Then what are the reasons for this phenomenon? Let's take a look at it.
出現因素：1）可能由于機頭前面的光纖頭有東西遮擋，比如（膠之類）。
Appearance factors: 1) may be due to the optical fiber head in front of the nose has something to block, such as (glue, etc.).
2）可能由于光纖頭螺母松動或者傾斜。
2) It may be due to loosening or tilting of the nut of the optical fiber head.
3）玻璃的表面有臟東西。
3) There is dirt on the surface of glass.
4）檢測距離太小，行走時有波動影響檢測。
4) The detection distance is too small and there are fluctuations when walking.
解決辦法：如果遇到上述問題的話，解決方法很簡單；1）清理干凈光纖頭，就可以。
Solution: If you encounter the above problems, the solution is simple; 1) Clean up the optical fiber head, you can.
2）傾斜或者松動，需要把它固定好，調整好。
2) tilt or loosen, it needs to be fixed and adjusted.
3)玻璃表面的臟東西會影響打膠等等，所以清理干凈玻璃表面就可。
3) The dirty things on the glass surface will affect the gluing and so on, so clean the glass surface can be.
4）調整合適的檢測距離。
4) Adjust the appropriate detection distance.
問題2.工作過程中總是有些不協調，各個動作之間不協調。
Question 2. There is always some disharmony in the process of work, and each action is not coordinated.
出現因素：1）參數設置有誤
Occurrence factors: 1) incorrect parameter setting
2）氣動系統配件老化。
2) Aging of pneumatic system accessories.
解決辦法：1）重新設置參數，或者使用原始參數。
Solution: 1) Reset the parameters or use the original parameters.
2）如果是氣動系統配件老化的話，就更換一個新的。
2) If the pneumatic system fittings are aging, replace a new one.

問題3、在行走過程或者傳送停止時，會出現一些玻璃渣。
Problem 3. Some glass slag will appear during the course of traveling or when the transmission stops.
出現因素：1）膠嘴護套損壞。
Occurrence factors: 1) Rubber nozzle sheath damage.
2）鋁槽深度檢測探頭行走時劃到玻璃。
2) Aluminum groove depth detection probe runs into the glass when walking.
3）刮膠板或者擋膠板的前進力量太大。
3) The forward force of the scraper or baffle is too large.
解決辦法：1）很簡單，重新換一個護套就可以。
Solution: 1) Simple, just change a new sheath.
2）調整探頭的位置，讓它在鋁槽中間行走。
2) Adjust the position of the probe and let it walk in the middle of the aluminium groove.
3）調節前進氣缸的速度到合適。可以避免出現玻璃渣。
3) Adjust the speed of the forward cylinder to a proper level. Glass slag can be avoided.
問題4.電機不穩定，時快時慢。
Problem 4. The motor is unstable, fast and slow.
這個問題也是比較簡單的。
This problem is also relatively simple.
問題因素：1）鋁槽不直。
Problem factors: 1) Aluminum groove is not straight.
2）導軌不直或者滑動軸承損壞。
2) The guide rail is not straight or the sliding bearing is damaged.
解決辦法：1）鋁槽要平直。
Solution: 1) Aluminum groove should be straight.
2）如果損壞或者導軌不直，可以更換。
2) If damaged or the guide rail is not straight, it can be replaced.
以上的精彩內容由雙組份打膠機廠家友情提供，更多的精彩內容請繼續關注我們：http://linshi.jncsjx.com，我們會有更多的精彩內容等你查看！
The above wonderful content is provided by the friendship of the two-component glue maker, more wonderful content please continue to pay attention to us: http://linshi.jncsjx.com, we will have more wonderful content waiting for you to see!