膠水的粘度關于電教質量的影響是十分大的，粘度過大，可能導致拉絲現象;多小的話，可能導致身染焊盤，所以挑選適宜的濃度關于硅膠點膠機的工作是十分重要的。在硅膠點膠機的運用過程中會遇到各種各樣的問題，可是只需你提早做好預備，了解硅膠點膠機的性能和參數，就必定能夠處理的。

　　The viscosity of glue has great influence on the quality of audio-visual education. Excessive viscosity can lead to the phenomenon of wire drawing. If it is small, it may lead to body dyed pad. Therefore, it is very important to select suitable concentration for silicone rubber dispenser. During the application of silicone dispensers, various problems will be encountered, but only if you prepare early, understand the performance and parameters of silicone dispensers, you will be able to deal with them.

　　溫度影響點膠機膠水的粘稠度和速度，在硅膠點膠機的工作中是一個非常重要的參數，點膠膠水在不必的時分一般存儲在冰箱中，運用之前半小時左右拿出來。膠水在運用的時分溫度應該控制在24攝氏度左右;別的，環境的溫度也對膠水有很大的影響，據測驗表明，環境溫度差5攝氏度的話，就會形成一半的點膠量改變，硅膠點膠機所以環境溫度的控制也是十分重要的。

　　The temperature affects the viscosity and speed of dispenser glue. It is a very important parameter in the work of silicone dispenser. Dispensing glue is usually stored in the fridge at no time, and it is taken out about half an hour before using. The glue should be controlled at 24 degrees Celsius in the temperature when the temperature of the environment; the other, also has a great effect on the glue, according to the test showed that the environmental temperature of 5 degrees Celsius, it will form a dispensing half the amount of change, so the environmental temperature control silicone dispensing machine is very important.

　　當膠流速變慢或者混膠不均時清洗混合器。將混合器拆下橫放在臺鉗上，夾住兩端蓋，不要夾到螺絲。用六角扳手松開兩端的六條螺絲，打開器體，取出墊片，擋針，混合芯。將各個零件清洗干凈。端蓋不要弄變形，各個平面不要有劃傷。

　　The mixer is cleaned when the flow rate is slow or the glue is uneven. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Release the six screws at both ends with a six angle wrench, open the body, remove the gasket, the needle, and the mixed core. Clean the parts. Do not deform the cover, and do not have any scratches in each plane.

　　槍口混合器清洗時直接擰下槍口混合器取出混合芯即可。清洗槍柄混合器時，先把槍上的定位螺絲松開，然后擰下槍柄混合器。槍口混合器同混合器同周期清洗;搶柄混合器同槍同周期清洗，半年或一年洗一次。

　　When the muzzle mixer is cleaned, the muzzle mixer is directly unscrewed out and the mixed core is removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer. The muzzle mixer is cleaned in the same cycle with the mixer; the shank mixer is cleaned with the gun in the same cycle, and is washed once in half a year or a year.

　　公司全方位服務于客戶，以質量上乘、價格合理和的售后服務與客戶攜手奮進，共同發展。質量保證，歡迎咨詢洽談。

　　The company serves the customer in all directions, with the high quality, the reasonable price and the perfect after sale service and the customers to advance hand in hand, and develop together. Quality assurance, welcome to consult the negotiation.