1、雙組份打膠機的基本工作流程如下：

　　1. The basic working process of the double component gluing machine is as follows:

　　(1)在打膠機的控制面板設定個好打膠機的打膠速度(默認也可以)

　　(1) first of all, in the control panel of the glue machine, set the glue speed of the glue machine (the default is also OK)

　　(2)將玻璃放入打膠機的工作區域

　　(2) put the glass into the working area of the glue machine

　　(3)當設備檢測到玻璃后吸盤會自動吸住玻璃以免玻璃在打膠過程中晃動或人為晃動正在進行打膠的玻璃

　　(3) when the device detects the glass sucker automatically so as not to suck the glass glass glue in the process of shaking in the shaking is glue or man-made glass

　　(4)當洗盤對玻璃固定好后，打膠機的機頭就開始對玻璃進行打膠動作(不需要進行對玻璃的厚度以及寬度進行設置，打膠機會自動調整并工作)

　　(4) when fixed on the glass pad, head of glue machine began to glass glue (without the need for action on the glass thickness and width setting, glue the opportunity to automatically adjust and work)

　　(5)以上的步驟重復3次將玻璃的4邊全部完成打膠后整個玻璃的打膠工作就算完成了。

　　(5) repeat the above steps 3 times, and complete the 4 sides of the glass. After gluing, the whole glass will be finished.

　　一般在默認的打膠速度每分鐘至少可以完成一款2米5見方的玻璃打膠工作，如果將打膠機的打膠速度加快生產會進一步提高。

　　Generally in the default beat speed, at least every minute can complete a 2 meters, 5 square glass punch work, if the glue machine to speed up the glue, production efficiency will further improve.

　　二、打膠機的特點

　　Two, the characteristics of glue machine

　　1、用高壓空氣在設定的時間內，使用腳踏開關或自動把液體推出。

　　1, use high pressure air in the set time, use pedal switch or automatic liquid launch.

　　2、點膠機控制器有點滴,連動,定時滴膠功能;點滴就是直接觸發腳踏開關滴膠,并且可通過時間控制點膠量精確度;連動就是用腳踏板之關閉時間多久來控制滴膠時間;定時滴膠就是觸發開關通過時間控制滴膠

　　2, dispensing controller with drip, linkage, timing function is directly trigger glue; drop foot switch glue, and through the dispensing time control accuracy; is used to control the closing time how long time the glue pedal linkage; timing trigger switch control is epoxy glue through time

　　3、自動雙組份打膠機采用高精度數碼定時控制器,精準控制每次滴定時間,精確到毫秒，正確地控制液料流量，絕不會浪費液料。

　　3 、 automatic double component glue machine adopts high precision digital timing controller, precisely control each titration time, accurate to millisecond, correctly control liquid material flow, will never waste liquid material.

　　4、只要調節好氣壓，出膠時間和選擇適當的針咀，便輕易改變每次注滴量和注滴時間。

　　4, as long as the adjustment of air pressure, the time to glue and choose the appropriate needle, it will easily change the amount of each drop and drip time.

　　5、調整自動點膠閥尾部調節螺絲和膠水的壓力可控制出膠量大小。膠量調節螺絲順時鐘向下轉動為減小膠量，逆時鐘方向轉動為 加大膠量。

　　5, adjust the automatic dispensing valve tail adjustment screw and glue pressure, can control the amount of glue. The glue volume adjusting screw is clockwise downward to reduce the glue quantity, and rotates in the counter clock direction to increase the adhesive quantity.

　　本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://linshi.jncsjx.com/謝謝您的到來!

　　The exciting content of this article comes from the two component dispenser, please click on our official website: http://linshi.jncsjx.com/, thank you for coming!