一、操作注意事項

　　I. operation notes

　　1、機頭電機下面不要有異物，遠離電機以免發生危險。

　　1, head motor, no foreign body, away from the motor, so as to avoid danger.

　　2、混膠或沖槍(沖洗混膠器、膠嘴)時，必須把機頭行走到軌道末端，用接膠板接住膠嘴內放出的膠，以免污染設備。

　　2, mix glue or blunt gun (rinse glue mixer, glue mouth) when, must move head to track end, use glue board to catch the glue that releases inside glue mouth, lest pollute equipment.

　　3.機頭前方檢測玻璃開關的光眼上不能有膠，否則誤工作。

　　3. front of the nose to detect glass switch, light eye can not have glue, or else work by mistake.

　　4、操作參數設置時，在控制箱pc顯示屏上進行，根據須要而選擇設定值，不要隨意設定，以免控制器發出錯誤的信息，影響打膠質量或損壞設備。

　　4, the operation parameters are set on the control box PC display screen, according to the need to select the set value, do not arbitrarily set, so as to avoid the controller to send wrong information, affect the quality of glue or damage equipment.

　　5、混膠或沖槍時，一定要先打開膠嘴控制閥門，然后再打開供膠機，以免壓力劇增損壞設備或者出現安全事故。

　　5, mixing glue or gun, must first open plastic mouth control valve, and then open the glue machine, so as to avoid pressure surge, damage to equipment or safety incidents.

　　6、吸盤上不能放石灰粉，如有膠請清理，如果有的玻璃邊緣正好放到吸盤的中心時，可調節吸盤左右移動.

　　6, the suction cup can not put lime powder, if there is glue, please clean up, if some glass edge just put into the center of the sucker, can adjust the suction cup move around

　　7、打膠時一定要扶好玻璃，避免玻璃脫離定位，影響打膠質量。

　　7, glue, we must help good glass, to prevent glass from positioning, affecting the quality of glue.

　　8、沖槍時先關閉機頭上的B膠出膠閥門，關閉B膠泵，然后打開B膠回流閥門，后沖槍，沖洗至出膠口不出黑膠，沖洗才能結束。

　　8, when the gun, first off the nose on the B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally blunt gun, rinse to the glue mouth, no black glue, rinse to finish.

　　9、打三玻時要將鋁框檢測探針缷掉，雙玻時在安裝上。

　　9, three glass to the aluminum frame detection probe off off, when the installation of double glass.

　　10、膠嘴和兩側的刮膠板如膠多時要清理。

　　10, rubber and both sides of the scraping board, such as glue for a long time to clean up.

　　二、維護與保養

　　Two 、 maintenance and maintenance

　　1、定期檢查電氣接線是否有松動及接地可靠性。

　　1 、 regularly check whether the electrical wiring is loose and the reliability of the grounding.

　　2、新機器經過一段時間的運轉之后，應全面檢查各緊固件是否有松動現象，并重新緊固。

　　2, after a period of operation of the new machine, should be fully checked whether the fasteners are loose, and re tightened.

　　3、定期清理混膠器及其前后管道內的凝結膠，定期清理止回閥;發現阻力增高或者堵塞現象，要及時清理。

　　3, regular cleaning of rubber mixing device and its front and back pipes of condensation glue, regularly cleaning the check valve; found resistance increased or blocked phenomenon, should promptly clean up.

　　4、每次使用完畢，要將機器上的殘膠及灰塵清除干凈，使機器保持清潔。

　　4. After each use, remove the residual glue and dust from the machine and keep the machine clean.

　　本文由雙組份打膠機為您提供，我們的網站是:http://www.xyspace.net/我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問!

　　This article is made up of a two component press machine. Our website is: http://www.xyspace.net/, we will provide you with better service with your wholehearted enthusiasm, and welcome your visit!